D88尊龙

你好,歡迎來到濟南D88尊龙環能燃氣發電設備有限公司官方網站!

沼氣天然氣瓦斯發電機組點火提前角的檢查

來源:http://dgxcbw.com   發布于:2017-10-30

1、12缸、6缸發動機磁電機點火系統
1, 12 cylinder, 6 cylinder engine magneto ignition system
松開磁電機與齒輪箱連接的兩螺栓,順時針或逆時針旋轉磁電機,即可調整點火提前角。面向磁電機正面面板,把磁電機按順時針方向旋轉,可將點火提前角向滯后方向調整(調小)約6.7°曲軸轉角;把磁電機按逆時針方向旋轉,可將點火提前角向提前方向調整(調大)約6.7°曲軸轉角。
Loosen the two bolts connected to the gear box and rotate the motor clockwise or counterclockwise to adjust the ignition advance angle. The magnet motor front panel, the magnet motor rotates clockwise, the ignition advance angle to the direction of adjustment (small) lag about 6.7 degree crank angle; the magnet motor rotates counterclockwise, the ignition advance angle to adjust the direction of advance (turn) of about 6.7 degree crank angle.
每次調節完畢后,再用拖動法檢驗,直到調整到需要的精確值。
After each adjustment, then drag test, until adjusted to the exact value required.
2、點火盒數字點火系統
2. Ignition box digital ignition system
D88尊龙調節點火控制器側面的調節旋鈕,即可調整點火提前角。向數字增大的方向調節(順時針調節)旋鈕,點火提前角增大;向數字減小的方向調節(逆時針調節)旋鈕,點火提前角減小。

QQ截圖20171025151917.jpgThe ignition advance angle can be adjusted by adjusting the adjusting knob on the side of the ignition controller. Adjust the direction of the digital increase (clockwise adjustment) knob, ignition advance angle increases; to reduce the number of directions to adjust (counterclockwise adjustment) knob, ignition advance angle decreases.
3、4缸發動機磁電機點火系統
Magneto ignition system for 3 and 4 cylinder engines
當需要調整點火提前角時一,可以通過改變兩個線圈的位置,從而實現調整點火提前角的大小。
When the ignition advance angle needs to be adjusted, the ignition advance angle can be adjusted by changing the position of the two coils.
松開感應線圈與導向盤連接的螺栓,順時針或逆時針移動兩個感應線圈,即可調整點火提前角的大小,站在輸出端,面向飛輪,順時針移動感應線圈,可將點火提前角調小,逆時針移動感應線圈,可將點火提前角調大。調整完畢后,使兩個感應線圈處在同一條同心直線上并緊固。每次調節完畢后,再用倒拖法檢驗,直到調整到需要的精確值。
Loosen the induction coil and the guide plate of the bolt connection, clockwise or counterclockwise movement of two induction coils, you can adjust the ignition advance angle size, standing on the output side, facing the flywheel, moving clockwise induction coil, the ignition advance angle is small, moving counterclockwise induction coil, the ignition advance angle adjustment. After adjustment, make the two induction coils in the same concentric line and fasten. After each adjustment, check with the pull back method until the exact value is needed.
更多的關于沼氣發電機組的問題或者詳細的內容,請進入我們公司的網站:http://dgxcbw.com 網站中會有很多的內容僅供參考。
More questions about biogas generators or detailed content, please go to our company's website: http://dgxcbw.com website will have a lot of content for reference only.

上一篇:瓦斯發電機組配氣機構介紹
下一篇:沼氣發電機組的組成需要哪些部件?