D88尊龙

你好,歡迎來到濟南D88尊龙環能燃氣發電設備有限公司官方網站!

瓦斯發電機組機油冷卻器簡介

來源:http://dgxcbw.com   發布于:2017-10-23

瓦斯發電機組D88尊龙工作時,冷卻水從機油冷卻器前蓋進水口進入,經過銅管內部,從后蓋出水口流出。機油則從殼體右下側進油口進入,穿過鋁翼管間縫隙,按隔板限制方向遷回流動,從殼體左上側的出油口流出。機油與冷卻水流向相反,通過銅管和鋁翼管進行熱量交換,從而達到用冷卻水降低機油溫度的目的。

When the gas generating unit works, the cooling water enters from the water inlet of the front cover of the oil cooler, and passes through the inner copper pipe and flows out from the water outlet of the rear cover. The oil enters the oil inlet from the right lower side of the shell, passes through the gap between the aluminum wing tubes, flows back to the flow in the restricted direction of the clapboard, and flows out from the oil outlet at the left upper side of the shell. The oil is opposite to the cooling water flow, and the heat exchange is carried out by the copper tube and the aluminum fin tube, so as to reduce the oil temperature by cooling water.

瓦斯發電機組余熱回收

機油冷卻器前、后蓋上方各有一個放氣閥,在添加瓦斯發電機組低溫內循環水時將其旋開,可將冷卻水里的空氣排出,防止產生氣阻影響冷卻效果。

There is a vent valve at the top of the oil cooler and the back cover of the oil cooler. When the circulating water is added to the gas generator set, it will be unscrewed. The air in the cooling water can be discharged to prevent the air blocking and affect the cooling effect.

D88尊龙機油冷卻器前、后蓋下方各有一個放水螺塞,當環境溫度低于5℃時,停車將放水螺塞和放氣閥同時旋開,可放凈機油冷卻器內的積水,以免凍壞銅管、鋁翼管和前、后蓋。有條件的用戶可從一側放水螺塞或放氣閥座孔處接上壓力588kPa的壓縮空氣,向內吹4-5分鐘,直到另一側放水孔處看不到往外噴水氣為止。

D88尊龙The oil cooler of the front and the back cover below each have a drain screw and when the ambient temperature is lower than 5 DEG C, parking will drain plug and a bleed valve and turn on the net, can put the water in the oil cooler, to avoid freezing the brass, aluminum wing tube and the front and rear cover. Conditional users from one side drain plug or discharge valve seat hole connected with the pressure of the compressed air blowing inward 588kPa, 4-5 minutes, until the other side drain hole can not see the water spray out so far.

D88尊龙機油冷卻器外殼上、下方各有一個油塞。在更換機油濾清器濾芯前,將兩油塞同時旋開,可放凈機油冷卻器內的機油,以免將機油濾清器濾芯拉出時流出過多的機油、弄臟瓦斯發電機組。

There is an oil plug on the top and bottom of the oil cooler shell. Before changing the filter element of the oil filter, the two oil plug is unscrewed at the same time, the oil in the oil cooler can be put off, so as to avoid excessive oil from the oil filter element pulling out and fouling the gas generator set.

本文由瓦斯發電機組友情奉獻,更多有關的知識請點擊:http://dgxcbw.comD88尊龙我們將用先進的技術,真誠的態度,為您提供為全面的服務。我們將會陸續向大家奉獻,敬請期待。

D88尊龙In this paper, the gas generating unit friendship dedication, more relevant knowledge please click: http://dgxcbw.com, we will use the most advanced technology, the most sincere attitude, to provide you with the most comprehensive service. We will continue to dedicate to you, please look forward to.


上一篇:燃氣發電機組的優點
下一篇:內燃式焦爐煤氣發電機組的性能介紹